Tuesday, January 4, 2022

Corrosion And Heat Resistant 12% Chromium Steel: 410 Stainless Steel

410 stainless steel is a corrosion and heat resistant 12% chromium steel. It is the most widely used of the hardenable stainless steels. Heat treated 410 stainless steel has mechanical properties comparable to the engineering alloy steel AISI 4130, coupled with the additional benefit of good corrosion resistance. 410 stainless steel is highly resistant to atmospheric corrosion. Maximum corrosion resistance is obtained by hardening and polishing.
Because 410 stainless steel is an air hardening steel, it must be given a high preheat, at least 350-400°F before welding, and immediately given a full anneal before the weldment cools. Otherwise the metal will harden, and cracking is likely. Matching composition filler metals are available, AWS E410 covered electrodes and ER410 bare filler wire. Alloy 82 (AWS ERNiCr-3) filler wire has also been used. This nickel alloy is comparatively low strength, and therefore accommodates some of the strain which may otherwise contribute to cracking in the 410 stainless steel weldment.
Heat uniformly to 1200-1400°F, remove from furnace and air cool. This should result in Brinell hardness about 187. For maximum softness, heat to 1500-1650°F, furnace cool slowly to 1100°F, after which air cooling is permissible. Brinell hardness should be approximately 155. Heat to 1750-1850°F, soak at heat, and quench in oil. Light sections will also harden by air cooling. 410 will harden to some degree when heated 1500°F and over unless slowly cooled to below the critical temperature. Soak at heat at least one hour, longer for large sections, and air cool. Tempering 410 in the range 750-1050°F results in decreased impact toughness and somewhat reduced corrosion resistance.

Chemistry

 CrMnNiCSiPSFe
MIN11.50.08
MAX13.51.00.750.151.00.040.03Balance

Specifications

AMS 5504
ASTM A 240
EN 1.4006
UNS S41000
Werkstoff 1.4006

Inventory

410 Stainless Steel Flanges, 410 Stainless Steel Pipe Fittings

Common Trade Names

410, 410 Stainless

Features

  • Hardenable stainless steel which may be tempered as high as 1350°F to produce high impact toughness.
  • Oxidation resistant through 1500°F intermittently, 1200°F continuously.
  • Corrosion resistant.

Applications

Physical Properties

Density: 0.276 lb/inch3 
Melting Point: 2723°F
Modulus of Elasticity: 29 x 106 
Electrical Resistivity:
 343 ohm-circ mil/ft

Temperature, °F21293212001450
Coefficient* of Thermal Expansion, in/in°F x 10-65.56.26.56.6
Thermal Conductivity
Btu • ft/ft2 • hr • °F
14.416.6

* 70°F to indicated temperature.

Mechanical Properties

Tensile Properties, Typical Annealed Condition

Tensile Strength, ksi60 – 75
0.2% Yield Strength, ksi32 – 42
Elongation, %20 – 40
Reduction of Area, %50 – 75

Heat Treated Condition – 1″ Stainless Steel Round Bar (Oil Quenched from 1800°F)

Tempering Temperature, °F300500700105011501200130014001500
Tensile Strength, ksi193.5188.5181.6181.4124.1117.5113.0101.896.5131.8
0.2% Yield Strength149.8148.6143.6144.7110.3103.799.184.277.988.6
Elongation, %17.017.316.816.020.821.322.023.525.019.5
Reduction of Area, %56.859.760.761.167.266.166.568.869.959.6
Hardness, Brinell388388388361255235229207189257

* Above data from wilsonpipeline Pipe Industry Co., Limited

Related Posts:

  • Stainless Steel 316L (UNS S31600)SPECIFICATIONS: GRADE 316 / 316L | UNS S31600 / 31603 | ASTM/ASME A240 | Werkstoff 1.4404 / 04All 316L at wilsonpipeline Pipe is certified to 316/316L… Read More
  • Duplex UNS 31803SPECIFICATIONS: GRADE Duplex | UNS S31803 | ASTM/ASME A240 / F51 | Werkstoff 1.4462Zhejiang wilsonpipeline Pipe Industry Co., Limited is a professiona… Read More
  • Stainless Steel 304L (UNS S30400)SPECIFICATIONS: GRADE 304 / 304L | UNS S30400 / 30403 | ASTM/ASME A240 | Werkstoff 1.4301 / 07304L is one of the most widely used and versatile stainl… Read More
  • Super Duplex UNS 32760SPECIFICATIONS: GRADE Super Duplex | UNS S32760 | ASTM/ASME A240 / F53 | Werkstoff 1.4501Our stock of Super Duplex 32760 can be supplied in sheet, pla… Read More
  • Lean Duplex 2304 (UNS S32304)SPECIFICATIONS: GRADE Lean Duplex | UNS S32304 | ASTM/ASME A240 | Werkstoff 1.4362Lean duplex 2304 is a 23‰ Cr, 4‰ Nickel, Mo free duplex stainless st… Read More

0 comments:

Post a Comment

Standard Reference for Seamless Steel Pipe

 1. Seamless steel tube for structure (GB / T8162-1999) is a seamless steel pipe for general structure and mechanical structure. 2. Seamles...